Shopping Cart

0 item(s) in cart/ total: $0    view cart
Smoktech VMAX Stainless Steel VV  PV

Smoktech VMAX Stainless Steel VV PV

review
0
0
5
On sale $40.95
Retail Price:$99.95
Your Savings:$59.00(59%)
9 In Stock! - Usually ships in 48hr
Part Number:VMAX
The Smoktech VMAX VV (Variable Voltage).

The VMAX is adjustable from 3.0v to 6v in .1 volt increments.

The built in display will display output voltage, battery remaining voltage, atomizer resistance, power on/off, and LED on/off.

The Smoktech VMAX features a 5amp output.  The switch also is able to rotate 360 degrees so you will not get a stuck switch.

The Vmax is threaded for use with most 510 atomizers, cartomizers etc...

The VMAX uses 2 18350 batteries (NOT INCLUDED). 
You will also need to buy a separate battery charger as this unit does not have the capability to charge thru.

Vmax  settings:

UU- Power up
UD- Power down
SO- Power on/off
UC- Battery Check
DS - display information setting 
     *do- atomizer output voltage
     *du- battery output voltage
     *dR - atomizer ohm
LO- LED on/off

Power  Up:

1. Press the button 3 times in a row until "UU" is shown on the display.
2. When UU is shown on the display, leave the button idle for 2 seconds. The display will change to show the last voltage selected.
3. Once the voltage is displayed, each time you press the button the voltage will advance to the next higher setting: 3.1,3.2,3.3 etc. When you reach 6.0, it will rotate back to 3.0 and go up again.
4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.

Power  Down:

1. Press the button 4 times in a row until "UD" is shown on the display .
2. When UD is shown on the display , leave the button idle for 2 seconds. The display will change to show the last voltage selected.
4. Once the voltage is displayed, each time you press the button the voltage will advance to the next lower setting: 5.9,5.8,5.7 etc. When you reach 3.0, it will rotate back to 6.0 and go up again.
4. when you have reached the desired setting, leave the button idle for 2 second. The setting will be saved and VV will resume normal operation.

 Power On/Off:

1. Press the button 5 times in a row until "SO" is shown on the display.
2. When UD is shown on the display, leave the button idle for 2 seconds. The display will show the last setting, on or off .
4. Each time you press the button the display will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. If you selected "OF" the VV will go into standby mode.

Battery Check:

1. Press the button 6 times in a row until UC is shown on the display.
2. When UC is shown on the display, leave the button idle for 2 seconds, the digital display will show your battery voltage measurement.
3. The battery voltage will be displayed for 2 seconds, then the display will turn off.

Display Information Setting During Vaping:

1. Press the button 7 times in a row until DS is shown on the display,
2. When DS is shown on the display, leave the button for 2 seconds, the display will show the current setting: DO, DU or DR.
3. Each time you press the button, the setting will toggle among "DO" "DU" or "DR" ,
4. When "DO" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer working output voltage during your vaping;
5. When "DU" is chosen, leave the button idle for 2 second, the setting will be saved and the display will show your battery voltage during your vaping. 
6. When "DR" is chosen, leave the button idle for 2 seconds, the setting will be saved and the display will show your atomizer resistance during your vaping.

LED On/Off

1. Press the button 8 times in a row until "LO" is shown on the display.
2. When LO is shown on the display, leave the button idle for 2 seconds, the display will show the current setting: ON/OFF .
3. Each time you press the button, the setting will toggle between on/off.
4. When you have reached the desired setting, leave the button idle for 2 seconds. The setting will be saved and VV will resume normal operation.

Short Circuit Protection:

The display will show the below error code when there is a short circuit:

1. F1

2. F2

Related Items

Recently Viewed Items